Skip to content
Highland Park office · License #104.015636 · Monday–Friday, 8:00 AM–5:00 PM Current customers · Book online · (847) 926-0085
Homeowner guide · Quality

Roof installation mistakes, and the materials that matter

Most roofs don't fail because of the shingle. They fail at the nails, the flashing, the edges and the attic, the details a homeowner never sees from the driveway. Here's what goes wrong, how to spot it, and what to ask before you sign.

Complete residential roof replacement by Etruscan Roofing & Exteriors

Why installation matters more than the shingle

A shingle is tested in a lab. A roof is built on your house, in the weather, by a crew. The same shingle can last 15 years or 35 depending on how it was fastened, flashed and ventilated. That's also why standard manufacturer warranties cover defects in the shingle but exclude damage from improper installation, and why insurers can reduce or deny a claim when an adjuster finds installation problems.

The mistakes we find most often

Mistake What happens How to spot it
Wrong nailing: nails too high, too few, over-driven or angled Shingles don't seal and blow off in normal wind. Over-driven nails cut the mat; under-driven nails pop through the shingle above Missing or lifted shingles after moderate wind, bumps in the courses, exposed nail heads
Short or missing ice barrier at eaves and valleys Water backs up behind ice dams and leaks into walls and ceilings Stains on ceilings or walls near the outside edge of the house after a thaw
Reused or caulked flashing at chimneys, walls and skylights Caulk dries and cracks within a few years; old flashing doesn't fit new shingles Leaks around chimneys and dormers; heavy tar or caulk where metal should be
No drip edge, or drip edge lapped wrong Water wicks behind the gutter into the fascia and deck edge Rotted fascia, stained soffits, shingles sagging at the edge
Missing or wrong starter strip The first course isn't sealed, so wind lifts the roof from the edge Edge shingles lifting or flapping
Unbalanced ventilation: blocked soffits, or mixing ridge vents with box or gable vents A hot, damp attic bakes shingles from below, causes ice dams and mold, and can void the shingle warranty Very hot attic in summer, frost or damp wood in winter, curling shingles
Valleys done wrong: nails near the center, shingles cut short Concentrated water finds the nail holes Leaks where two roof slopes meet
Overlay instead of tear-off Hides rotted decking, traps heat, adds weight; not allowed over two or more existing layers Uneven, wavy surface; two layers visible at the edge
Soft or rotted decking left in place Nails don't hold; the roof sags and leaks early Spongy spots when walked on; sagging between rafters
Old pipe boots and vents reused Rubber collars crack in sun and cold and leak around the pipe Stains around bathroom fans and plumbing vents
Mixed brands of components The roof loses eligibility for the manufacturer's system warranty Ask what ridge cap, starter, underlayment and vents were used
Poor cleanup Nails left in the lawn and driveway Flat tires, nails in the grass weeks later

What the building code requires

Most Chicagoland towns build to the International Residential Code with local amendments. For a shingle roof that typically means an ice barrier from the eave to at least 24 inches inside the exterior wall, drip edge at eaves and rakes, approved underlayment, flashing at walls, chimneys and valleys, no new layer over a roof that already has two or more, and enough attic ventilation, generally 1 square foot of net free vent area for every 150 square feet of attic floor (1 per 300 in some cases), split between intake low and exhaust high. Your town's building department has the final word, and most towns require a permit for a re-roof.

The materials that matter

A roof is a system. The shingle is the part you see, but these are the parts that decide how long it lasts:

  • Shingle line and rating. For hail, look for a UL 2218 Class 4 impact rating (GAF Timberline UHDZ, Owens Corning Duration FLEX and STORM). For wind, look for the shingle's tested wind rating and the nail count it requires. See our shingle guide.
  • Ice and water barrier at the eaves, in valleys and around penetrations. It seals around nails and stops backed-up water.
  • Synthetic underlayment over the rest of the deck. It resists tearing and stays flat better than traditional felt.
  • Matched starter, hip and ridge from the same manufacturer, which seal properly and keep system warranties eligible.
  • Ventilation products sized to the attic: continuous soffit intake and ridge exhaust, not a mix of exhaust types.
  • New flashing: step flashing at walls, counter-flashing at chimneys, and new pipe boots. Copper where the house calls for it.
  • The right fasteners: corrosion-resistant roofing nails of the correct length, driven flush in the manufacturer's nailing zone.
  • Sound decking, with any soft or delaminated sheathing replaced before the roof goes on.

Questions to ask before you sign

Ask A good answer
Will you tear off down to the deck? Yes, and any bad decking is replaced at a stated price per sheet
What goes under the shingles, and where? Ice and water barrier at eaves and valleys, synthetic underlayment elsewhere, named products
Will you replace the flashing and pipe boots? New step flashing, counter-flashing and boots, not caulk over the old ones
How is the attic ventilated? They measured the attic and will balance intake and exhaust
Whose ridge cap and starter? The same manufacturer as the shingle
Which warranty, and who registers it? The contractor names the warranty and registers it for you
Will you pull the permit? Yes, in the company's name

How Etruscan builds a roof

Full tear-off, deck inspection and replacement of any bad sheathing, ice and water barrier at the eaves and valleys, synthetic underlayment, new drip edge, new flashing and pipe boots, balanced ventilation, matched components from one manufacturer, nails placed and driven to the manufacturer's spec, a permit in our name, a magnetic nail sweep every day, and a final walkthrough with you. It's the same on a simple ranch and on a slate estate.

Installed by Etruscan

From our projects

See the gallery
Quality residential roof installation by Etruscan Roofing & Exteriors
Slate roof installation by Etruscan Roofing & Exteriors
Copper roof installation by Etruscan Roofing & Exteriors
New roof gutter installation by Etruscan Roofing & Exteriors

Ready to talk it through? Our services: Roof replacement · Roof repair · Attic insulation & ventilation

Roof installation mistakes questions

Does the manufacturer's warranty cover installation mistakes?

A standard shingle warranty covers manufacturing defects, not workmanship. Damage caused by improper installation is usually excluded. Some manufacturers offer enhanced system warranties that add workmanship coverage, but only when a certified contractor installs the full system of matching components and the warranty is registered.

Can a new roof go over my old one?

Sometimes, but we rarely recommend it. Model building code doesn't allow a new layer over a roof that already has two or more layers, a second layer hides soft or rotted decking, and an overlay can shorten the new roof's life and complicate insurance claims later. A full tear-off lets us inspect and fix the deck.

How can I tell if my roof was installed badly?

From the ground, look for shingles lifting or blowing off in normal wind, wavy or uneven lines, exposed nail heads, stains on ceilings near chimneys or walls, and thick icicles in winter. In the attic, look for daylight, damp sheathing, frost or mold. A careful inspection with photos will show nailing, flashing and ventilation problems.

Are more expensive shingles always better?

Not always. A mid-range shingle installed correctly with the right underlayment, ice barrier, flashing and ventilation will outlast a premium shingle installed poorly. Pay for a better shingle when you want higher impact or wind ratings, a longer warranty, or a particular look.

Sources and further reading

Manufacturer figures are the manufacturer's own ratings. Products and warranties change; we confirm current specs before every quote.

  1. GAF: shingle nails and nail placement
  2. Roofing sections of the International Residential Code (index)
  3. IDFPR: Hiring a licensed roofer (consumer brochure)
Book your free estimate online Pick a time that works for you. You'll get a confirmation by email and text right away.
Book online
Call (847) 926-0085 Book online